resistance of a wire
...se wandering electrons are called conduction electrons and the more of these there are, for a given volume of metal, the better the metal will be as a conductor of electricity. When you connect a battery across a wire, one end becomes +ve and attracts the conduction electrons, which drift towards that end of the wire. But the electrons have obstacles to face because the metal atoms are jiggling about because of their thermal energy and so the electrons collide with them and are knocked all over. It¡¦s this difficulty that the electrons have in moving along the wire that we call resistance. Resistance involves collisions of the current-carrying charged particles with fixed particles that make up the structure of the conductors. A resistor is a material that makes it hard for electrons to go through a circuit. Without resistance, the amount from even one volt would be infinite. Resistance occurs when electrons travelling along the wire collide with the atoms of the wire. The unit of resistance is OHMS. The higher the resistance, the lower the current. If there is high resistance, to get the same current a higher voltage will be needed to provide an extra push for the electricity. Some metals have less resistance than others. Wires are always made out of copper because copper has a low resistance and therefore it is a good conductor. The length and width of a wire also has an effect. In this investigation I will investigate how the diameter of a wire will affect the resistance in the circuit.. Resistance opposes the flow of an electric current around a circuit so that energy is required to push the charged particles around the circuit. The circuit itself can resist the flow of particles if the wires are either very thin or very long. E.g. The filament in an electric light bulb Ohm's law He discovered relationship that the amount of steady current through a large number of materials is directly proportional to the potential difference, or voltage, across the materials. Thus, if the voltage V (in units of volts) between two ends of a wire made from one of these materials is tripled, the current I (amperes) also triples; and the quotient V/I remains constant. The quotient V/I for a given piece of material is called its resistance, R, measured in units named ohms. The resistance of materials for which Ohm's law is valid does not change over enormous ranges of voltage and current. Ohm's law may be expressed mathematically as V/I = R. That the resistance, or the ratio of voltage to current, for all or part of an electric circuit at a fixed temperature is generally constant had been established by 1827 as a result of the investigations of the German physicist George Simon Ohm. Alternate statements of Ohm's law are that the current I in a conductor equals the potential difference V across the conductor divided by the resistance of the conductor, or simply I = V/R, and that the potential difference across a conductor equals the product of the current in the conductor and its resistance, V = IR. In a circuit in which the potential difference, or voltage, is constant, the current may be decreased by adding more resistance or increased by removing some resistance. Ohm's law may also be expressed in terms of the electromotive force, or voltage, E, of the source of electric energy, such as a battery. For example, I = E/R. With modifications, Ohm's law also applies to alternating-current circuits, in which the relation between the voltage and the current is more complicated than for direct currents. Precisely because the current is varying, besides resistance, other forms of opposition to the current arise, called reactance. The combination of resistance and reactance is called impedance, Z. When the impedance, equivalent to the ratio of voltage to current, in an alternating current circuit is constant, a common occurrence, and Ohm¡¦s law is applicable. For example, V/I = Z. With further modifications Ohm's law has been extended to the constant ratio of the magneto motive force to the magnetic flux in a magnetic circuit. Resistance values in electronic circuits vary from a few ohms, W, to values in kilohms, kW, (thousands of ohms) and megohms, MW, (millions of ohms). Electronic components designed to have particular resistance values are called resistors. Prediction My hypothesis is that the thinner the wire, the higher the resistance. The thicker the wire, the lower the resistance. This is because the thinner the wire is, the less paths there are for electrons in the wire therefore the harder it is for current to flow. This results in the energy not being able to spread out as much, so the resistance will be higher. This theory is similar to that of a door, where people represent the electrons and the door represents the diameter of the wire. If the door is wider, more people can get through, more easily. If the door is small, people have more difficulty and not as many people can walk in or out of the door. It is the same principal for electrons. If the diameter of a wire is thicker more electrons can go through the wire, therefore less resistance. The atoms from the metals cannot stop or collide with as many electrons because the diameter of the wire is larger. This can be seen in the diagram on the next page. From my preliminary work, I can see that if the area of the wire doubles, so does the number of possible routes for the current to flow down, therefore the flow of electrons are twice as spread out, so resistance might halve, i.e. Resistance 1/Area. This can be explained using the formula: R = V/I Where R=Resistance, I= Current, V=Voltage When there is twice the current, and the voltage is the same, R (resistance) will halve. I did some research and in a book called ¡¥Ordinary Level Physics¡¦ By A. F. Abbott, it says ¡¥that doubling the area will therefore halve the resistance¡¦- in other words the resistance of a wire is inversely proportional to its area, or R 1/A, but we are measuring diameter so the following calculations have to be made: Safety Whilst doing the investigation, it is important to keep safety into consideration. The scissors should only be used for cutting the wire to the appropriate length and for no other reason. Before using the power pack, the pointer should point at 0 volts. It is important to be careful while using the power supply. While handling live wires, it is essential to be careful. The voltage should be kept low because of the safety factor and the wires heating up. Reliability To make the experiment reliable, all apparatus must be checked to see if it is functioning properly and is giving a true reading. This will partly avoid systematic error. Another way to make the experiment reliable is to use two methods: to do the investigation in two different ways to measure the resistance when the diameters are changed. If one method contains systematic error or is very inaccurate, the other method will be used to recognise that. Precision I will take as many different results as possible so that there a wide range of results and that I am able to arrive at a good conclusion. To increase the accuracy of the experiment I will do repeats for all the experiments so when the mean is taken, an accurate table is drawn up and if one result is anonymous the other two results would contrast the anonymous result. Preliminary work „« Whilst doing preliminary work I will investigate the following: „« Get some sort of idea whether there is a connection between the diameter of the wire and the resistance within the circuit. „« Find out what kind of figures the resistance are for different diameters. „« Write the results of the preliminary work in a table below. „« Find out what length of wire should be used throughout the experiment. „« Find the appropriate apparatus and use them. „« Investigate ways of making the experiment fairer and more reliable. „« Think about two methods of doing the investigation to make it more reliable and refine methods of doing the investigation. „« Think about what materials (two: to make sure my conclusion works for all materials) should be used. „« Investigate the range of results, which will be appropriate and can be plotted in a graph to show some sort of connection. „« Think about what diameters or gauges should be used and state why they are being used. „« The verification of techniques is important whilst doing preliminary work and to decide adjustments, which will have to be made whilst having precision and reliability in mind. „« Think about the appropriate length of the wire whilst doing the investigation. This can be found whilst doing preliminary work. The appropriate length will be one, which is easy to work with and has more precision. Preliminary Method The aim of preliminary work is to find apparatus, make adjustments and investigate other factors listed above. With this in mind it is important to collect sufficient data but it is important not too contain too much data. The preliminary work is not designed for collecting data but for investigating the factors above. It is for this reason that the extremes will be taken. This means the highest and lowest diameter that can be obtained will be used as well as one or two in the middle. The three materials, which are available in more than three diameters, will be tested and in the conclusion, the best two materials will be stated. It is also important to find the appropriate length so a 50cm and 100cm length of wire will be tested and again in the conclusion, the most appropriate length of wire will be stated. The apparatus will be set up as shown in the diagram. A piece of wire will be cut of 50 cm and 100cm (They will both be tested). The 50cm wire will be placed in the middle of the circuit. It will be placed on the ruler and stuck down with masking tape. Crocodile clips will be placed on either side of the wire and the resistance will be measured using an ohmmeter. Three materials will be tested and two materials will be picked out of Constantan, copper and nichrome. The investigation will be carried out of carry out by measuring the resistance of different materials and two different lengths of wire. This will be done using an ohmmeter and the resistances of different diameters of different materials will be measured in ohms. The range of results will be investigated and decide whilst doing the preliminary work. The resistance of different diameters of wire will be measured whilst keeping other variables such as length and material constant. The results will be written down in a results table on the next page. I will find resistances of three different materials in order to decide which material will be used. In the real experiment the second method will also be used by which the resistance can be calculated by finding the potential difference and the current and using the formulae below to calculate the resistance as a test if the method is easy and it works. In the preliminary work, it...